Hi, I’m not quite sure if this vhdl code and testbench is correct for the given task. Can you take a look?

Design a one-hour kitchen timer. The device should have buttons/switches to start and stop the timer, as well as to set the desired time interval for the alarm. Realize the task using the software package Quartus or in GHDL, confirm the correctness of the project task by simulation.

This is VHDL code:

use ieee.std_logic_1164.all;
use ieee.numeric_std.all;

entity Kitchen_Timer is
  port (
    clk   : in std_logic;    -- Clock input
    reset : in std_logic;    -- Reset input
    start : in std_logic;    -- Start button input
    stop  : in std_logic;    -- Stop button input
    alarm : out std_logic    -- Alarm output
  );
end entity Kitchen_Timer;

-- Declare the architecture for the kitchen timer
architecture Behavioral of Kitchen_Timer is
  signal count     : integer range 0 to 3600 := 0;   -- Counter for timer
  signal alarming  : std_logic := '0';               -- Signal to indicate alarming interval
  signal alarm_en  : std_logic := '0';               -- Signal to enable alarming interval
  signal alarm_cnt : integer range 0 to 600 := 0;    -- Counter for alarming interval
begin
  -- Process to control the kitchen timer and alarming interval
  process (clk, reset)
  begin
    if (reset = '1') then
      count     <= 0;
      alarming  <= '0';
      alarm_en  <= '0';
      alarm_cnt <= 0;
    elsif (rising_edge(clk)) then
      if (stop = '1') then
        count     <= 0;
        alarming  <= '0';
        alarm_en  <= '0';
        alarm_cnt <= 0;
      elsif (start = '1' and count < 3600) then
        count <= count + 1;
        if (count = 3600) then
          count     <= 0;
          alarming  <= '0';
          alarm_en  <= '0';
          alarm_cnt <= 0;
        elsif (count > 0) then
          alarm_en <= '1';
        end if;
      end if;

      if (alarm_en = '1') then
        if (alarm_cnt < 600) then
          alarm_cnt <= alarm_cnt + 1;
        else
          alarm_cnt <= 0;
          alarming  <= '1';
        end if;
      end if;
    end if;
  end process;

  -- Assign the alarm output
  alarm <= alarming;
end architecture Behavioral; ```

This is Testbench:

```library ieee;
use ieee.std_logic_1164.all;

entity tb_Kitchen_Timer is
end tb_Kitchen_Timer;

architecture tb of tb_Kitchen_Timer is

    component Kitchen_Timer
        port (clk   : in std_logic;
              reset : in std_logic;
              start : in std_logic;
              stop  : in std_logic;
              alarm : out std_logic);
    end component;

    signal clk   : std_logic;
    signal reset : std_logic;
    signal start : std_logic;
    signal stop  : std_logic;
    signal alarm : std_logic;

    constant TbPeriod : time := 1000 ns; -- EDIT Put right period here
    signal TbClock : std_logic := '0';
    signal TbSimEnded : std_logic := '0';

begin

    dut : Kitchen_Timer
    port map (clk   => clk,
              reset => reset,
              start => start,
              stop  => stop,
              alarm => alarm);

    -- Clock generation
    TbClock <= not TbClock after TbPeriod/2 when TbSimEnded /= '1' else '0';

    -- EDIT: Check that clk is really your main clock signal
    clk <= TbClock;

    stimuli : process
    begin
        -- EDIT Adapt initialization as needed
        start <= '0';
        stop <= '0';

        -- Reset generation
        -- EDIT: Check that reset is really your reset signal
        reset <= '1';
        wait for 100 ns;
        reset <= '0';
        wait for 100 ns;

        -- EDIT Add stimuli here
        wait for 100 * TbPeriod;

        -- Stop the clock and hence terminate the simulation
        TbSimEnded <= '1';
        wait;
    end process;

end tb;

-- Configuration block below is required by some simulators. Usually no need to edit.

configuration cfg_tb_Kitchen_Timer of tb_Kitchen_Timer is
    for tb
    end for;
end cfg_tb_Kitchen_Timer;```

 #science
  • dejo@kbin.socialOP
    1·
    1 year ago

    @T4V0 Thanks for the answer, but I think I didn’t understand you very well, can you send me the code with the modifications so that I know what exactly you mean?
    Thank you very much, in advance

    • T4V0@kbin.social
      1·
      1 year ago

      @dejo

      can you send me the code with the modifications so that I know what exactly you mean?

      I would rather not, as it isn’t a good learning experience for you, and would require some time for me to write the code.

      Though if you have any questions about my previous answer, feel free to ask me about it.

      As a freebie for you, pay attention to the alarming signal, and the condition that has been set: “The device should have buttons/switches to start and stop the timer, as well as to set the desired time interval for the alarm.”. If I wanted the alarm to ring after 50 minutes, how would I do that? And what happens when the timer starts?

      From the code I see here, the alarm is going to ring 10 minutes after being started, and it won’t stop until an hour passes. And it has no way to set a time for it to ring, it always rings after 10 minutes.

      And, not only that, the start signal is never set in the testbench, so the timer is never going to begin.

      • dejo@kbin.socialOP
        2·
        1 year ago

        @T4V0 Hello, I’ve been doing a lot of research on this project these days and I’ve brought the code to a better level, I hope… But I’m not sure if this simulation…

        This is VHDL code:
        library ieee;

        use ieee.std_logic_1164.all;

        use ieee.numeric_std.all;

        entity Kitchen_Timer is

        port (

        clk : in std_logic; – Clock input

        reset : in std_logic; – Reset input

        start : in std_logic; – Start button input

        stop : in std_logic; – Stop button input

        adjust_interval_up : in std_logic; – Button for increasing alarm interval

        adjust_interval_down : in std_logic; – Button for decreasing alarm interval

        alarm : out std_logic – Alarm output

        );

        end entity Kitchen_Timer;

        architecture Behavioral of Kitchen_Timer is

        signal count : integer range 0 to 3600000 := 0; – Adjust range for 1 hour

        signal alarming : std_logic := ‘0’;

        signal alarm_interval : integer range 600 to 3600000 := 600; – Adjust range for 1 hour

        begin

        process (clk, reset)

        begin

        if reset = ‘1’ then

        count &lt;= 0;

        alarming &lt;= ‘0’;

        alarm_interval &lt;= 600;

        elsif rising_edge(clk) then

        if start = ‘1’ then

        count &lt;= count + 1;

        end if;

        if stop = ‘1’ or count = alarm_interval then

        count &lt;= 0;

        end if;

        if adjust_interval_up = ‘1’ then

        if alarm_interval &lt; 3600000 then

        alarm_interval &lt;= alarm_interval + 600; – Adjust increment for 1 minute

        end if;

        elsif adjust_interval_down = ‘1’ then

        if alarm_interval > 600 then

        alarm_interval &lt;= alarm_interval - 600; – Adjust decrement for 1 minute

        end if;

        end if;

        end if;

        end process;

        alarming &lt;= ‘1’ when count >= alarm_interval else ‘0’;

        alarm &lt;= alarming;

        end architecture Behavioral;

        This is Testbench:
        library ieee;

        use ieee.std_logic_1164.all;

        entity tb_Kitchen_Timer is

        end tb_Kitchen_Timer;

        architecture tb of tb_Kitchen_Timer is

        component Kitchen_Timer

        port (

        clk : in std_logic;

        reset : in std_logic;

        start : in std_logic;

        stop : in std_logic;

        adjust_interval_up : in std_logic;

        adjust_interval_down : in std_logic;

        alarm : out std_logic

        );

        end component;

        signal clk : std_logic := ‘0’;

        signal reset : std_logic := ‘0’;

        signal start : std_logic := ‘0’;

        signal stop : std_logic := ‘0’;

        signal adjust_interval_up : std_logic := ‘0’;

        signal adjust_interval_down : std_logic := ‘0’;

        signal alarm : std_logic;

        constant TbPeriod : time := 1 us; – Set the clock period to 1us

        signal TbClock : std_logic := ‘0’;

        signal TbSimEnded : std_logic := ‘0’;

        begin

        dut : Kitchen_Timer

        port map (

        clk => clk,

        reset => reset,

        start => start,

        stop => stop,

        adjust_interval_up => adjust_interval_up,

        adjust_interval_down => adjust_interval_down,

        alarm => alarm

        );

        -- Clock generation

        TbClock &lt;= not TbClock after TbPeriod/2 when TbSimEnded /= ‘1’ else ‘0’;

        clk &lt;= TbClock;

        stimuli : process

        begin

        -- Reset generation

        reset &lt;= ‘1’;

        wait for 20 us; – Adjust delay to fit the new clock period

        reset &lt;= ‘0’;

        -- Add your stimuli and test cases here

        -- For example:

        start &lt;= ‘1’;

        wait for 50 us; – Adjust delay to fit the new clock period

        start &lt;= ‘0’;

        wait for 400 us; – Adjust delay to fit the new clock period

        adjust_interval_up &lt;= ‘1’;

        wait for 20 us; – Adjust delay to fit the new clock period

        adjust_interval_up &lt;= ‘0’;

        wait for 50 us; – Adjust delay to fit the new clock period

        adjust_interval_down &lt;= ‘1’;

        wait for 20 us; – Adjust delay to fit the new clock period

        adjust_interval_down &lt;= ‘0’;

        wait for 50 us; – Adjust delay to fit the new clock period

        -- …

        -- Stop the clock and hence terminate the simulation

        TbSimEnded &lt;= ‘1’;

        wait;

        end process;

        end tb;

        -- Configuration block below is required by some simulators. Usually no need to edit.

        configuration cfg_tb_Kitchen_Timer of tb_Kitchen_Timer is

        for tb

        end for;

        end cfg_tb_Kitchen_Timer;
        And this is result of simulation:

        • T4V0@kbin.social
          1·
          1 year ago

          @dejo This is much better, but there is still some room for improvement.

          There is a mismatch between your comparisons count and alarm_interval. Here in the code bellow you can see the issue:

          if stop = '1' or count = alarm_interval then

count &lt;= 0; -- count is 0 here

end if;

[...]

alarming &lt;= '1' when count >= alarm_interval else '0'; -- This condition is never true due to count always being 0 or smaller the alarm_interval.
alarm &lt;= alarming;

          As it is right now, the alarming signal is never going to be ‘1’. It is best to split the comparison and write to alarming directly:

          if stop = '1' then

count &lt;= 0;
alarming &lt;= '0';

end if;

if count = alarm_interval then

alarming &lt;= '1';

end if;

[...]

alarm &lt;= alarming;

          As for the testbench, you should set the start and unset it only after the alarming is ‘1’, and test if alarming is working after adjusting the timer:

          stimuli : process

begin

-- Reset generation

reset &lt;= '1';

wait for 20 us; -- Adjust delay to fit the new clock period

reset &lt;= '0';

-- Add your stimuli and test cases here

-- For example:

start &lt;= '1';
stop &lt;= '0';

wait for 620 us; -- Wait until alarm is alarming

start &lt;= '0'
stop &lt;= '1';
adjust_interval_up &lt;= '1';

wait for 1 us; -- Increment the timer by a minute

start &lt;= '1';
stop &lt;= '0';
adjust_interval_up &lt;= '0';

wait for 1220 us; -- Wait until the alarm is alarming

start &lt;= '0';
stop &lt;= '1';
adjust_interval_down &lt;= '1';

wait for 1 us; -- Decrement the timer by a minute

start &lt;= '1';
stop &lt;= '0';
adjust_interval_down &lt;= '0';

wait for 620 us; -- Wait until the alarm is alarming

start &lt;= '0';
stop &lt;= '1';

wait for 20 us;

-- ...

-- Stop the clock and hence terminate the simulation

TbSimEnded &lt;= '1';

wait;

end process;

          I suggest changing the 100 ms time slices you use in the timer to a minute instead. That way your simulation time could be much quicker (though you would also have to change the testbench delays).

          • dejo@kbin.socialOP
            2·
            1 year ago

            @T4V0 I
            In the meantime, I worked on improving the code.

            VHDL code:
            llibrary ieee;
            use ieee.std_logic_1164.all;
            use ieee.numeric_std.all;

            entity Kitchen_Timer is
            port (
            clk : in std_logic; – Clock input
            reset : in std_logic; – Reset input
            start : in std_logic; – Start button input
            stop : in std_logic; – Stop button input
            adjust_interval_up : in std_logic; – Button for increasing alarm interval
            adjust_interval_down : in std_logic; – Button for decreasing alarm interval
            alarm : out std_logic – Alarm output
            );
            end entity Kitchen_Timer;
            architecture Behavioral of Kitchen_Timer is
            signal count : integer range 0 to 3600000 := 0; – Adjust range for 1 hour
            signal alarming : std_logic := ‘0’;
            signal alarm_interval : integer range 600 to 3600000 := 600; – Adjust range for 1 hour
            begin
            process (clk, reset)
            begin
            if reset = ‘1’ then
            count &lt;= 0;
            alarm_interval &lt;= 600;
            elsif rising_edge(clk) then
            if start = ‘1’ then
            count &lt;= count + 1;
            end if;
            if stop = ‘1’ or count = alarm_interval then
            count &lt;= 0;
            end if;
            if adjust_interval_up = ‘1’ then
            if alarm_interval &lt; 3600000 then
            alarm_interval &lt;= alarm_interval + 600; – Adjust increment for 1 minute
            end if;
            count &lt;= 0; – Reset count when adjusting interval
            elsif adjust_interval_down = ‘1’ then
            if alarm_interval > 600 then
            alarm_interval &lt;= alarm_interval - 600; – Adjust decrement for 1 minute
            end if;
            count &lt;= 0; – Reset count when adjusting interval
            end if;
            end if;
            end process;
            alarming &lt;= ‘1’ when count >= alarm_interval else ‘0’;
            alarm &lt;= alarming;
            end architecture Behavioral;

            Testbench:

            library ieee;
            use ieee.std_logic_1164.all;

            entity tb_Kitchen_Timer is
            end tb_Kitchen_Timer;
            architecture tb of tb_Kitchen_Timer is
            component Kitchen_Timer
            port (
            clk : in std_logic;
            reset : in std_logic;
            start : in std_logic;
            stop : in std_logic;
            adjust_interval_up : in std_logic;
            adjust_interval_down : in std_logic;
            alarm : out std_logic
            );
            end component;
            signal clk : std_logic := ‘0’;
            signal reset : std_logic := ‘0’;
            signal start : std_logic := ‘0’;
            signal stop : std_logic := ‘0’;
            signal adjust_interval_up : std_logic := ‘0’;
            signal adjust_interval_down : std_logic := ‘0’;
            signal alarm : std_logic;
            constant TbPeriod : time := 20 ns;
            signal TbClock : std_logic := ‘0’;
            signal TbSimEnded : std_logic := ‘0’;
            begin
            dut : Kitchen_Timer
            port map (
            clk => clk,
            reset => reset,
            start => start,
            stop => stop,
            adjust_interval_up => adjust_interval_up,
            adjust_interval_down => adjust_interval_down,
            alarm => alarm
            );
            -- Clock generation
            TbClock &lt;= not TbClock after TbPeriod/2 when TbSimEnded /= ‘1’ else ‘0’;
            clk &lt;= TbClock;
            stimuli : process
            variable num_ticks : natural;
            begin
            -- Reset generation
            reset &lt;= ‘1’;
            wait for 200 us;
            reset &lt;= ‘0’;
            wait for 200 us;
            -- Start the timer
            start &lt;= ‘1’;
            wait for 500 us;
            -- Adjust interval up and down
            adjust_interval_up &lt;= ‘1’;
            wait for 100 us;
            adjust_interval_up &lt;= ‘0’;
            wait for 100 us;
            adjust_interval_down &lt;= ‘1’;
            wait for 100 us;
            adjust_interval_down &lt;= ‘0’;
            wait for 100 us;
            -- Wait for the timer to reach the alarm interval (3600000 clocks)
            wait for 72 ms; – Simulate for the required time
            -- Stop the timer
            start &lt;= ‘0’;
            wait for 300 us;
            -- Stop the clock and terminate the simulation
            TbSimEnded &lt;= ‘1’;
            wait;
            end process;
            end tb;

            And this is simulation:

            • T4V0@kbin.social
              1·
              1 year ago

              @dejo I have made a few changes to your code:

              Kitchen_Timer.vhd

              library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;

entity Kitchen_Timer is
    port
    (
        clk                  : in std_logic; -- Clock input
        reset                : in std_logic; -- Reset input
        start                : in std_logic; -- Start button input
        stop                 : in std_logic; -- Stop button input
        adjust_interval_up   : in std_logic; -- Button for increasing alarm interval
        adjust_interval_down : in std_logic; -- Button for decreasing alarm interval
        alarm                : out std_logic -- Alarm output
    );
end entity Kitchen_Timer;
architecture Behavioral of Kitchen_Timer is
    signal count          : integer range 0 to 60 := 0; -- Adjust range for 1 hour
    signal alarming       : std_logic             := '0';
    signal alarm_interval : integer range 1 to 60 := 1; -- Adjust range for 1 hour
begin
    process (clk, reset)
    begin
        if reset = '1' then
            count          &lt;= 0;
            alarm_interval &lt;= 1;
        elsif rising_edge(clk) then
            if start = '1' then
                count &lt;= count + 1;
            end if;
            if stop = '1' then
                count    &lt;= 0;
                alarming &lt;= '0';
            end if;
            if count = alarm_interval then
                alarming &lt;= '1';
            end if;
            if adjust_interval_up = '1' then
                if alarm_interval &lt; 60 then
                    alarm_interval &lt;= alarm_interval + 1; -- Adjust increment for 1 minute
                end if;
                count &lt;= 0; -- Reset count when adjusting interval
            elsif adjust_interval_down = '1' then
                if alarm_interval > 60 then
                    alarm_interval &lt;= alarm_interval - 1; -- Adjust decrement for 1 minute
                end if;
                count &lt;= 0; -- Reset count when adjusting interval
            end if;
        end if;
    end process;
    alarm &lt;= alarming;
end architecture Behavioral;

              tb_Kitchen_Timer.vhd

              library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;

entity tb_Kitchen_Timer is
end tb_Kitchen_Timer;

architecture tb of tb_Kitchen_Timer is
    signal clk                  : std_logic := '0';
    signal reset                : std_logic := '0';
    signal start                : std_logic := '0';
    signal stop                 : std_logic := '0';
    signal adjust_interval_up   : std_logic := '0';
    signal adjust_interval_down : std_logic := '0';
    signal alarm                : std_logic;
    constant TbPeriod           : time      := 10 ns;
    signal TbClock              : std_logic := '0';
    signal TbSimEnded           : std_logic := '0';
begin
    dut : entity work.Kitchen_Timer
    port map
    (
        clk                  => clk,
        reset                => reset,
        start                => start,
        stop                 => stop,
        adjust_interval_up   => adjust_interval_up,
        adjust_interval_down => adjust_interval_down,
        alarm                => alarm
    );

    -- Clock generation
    TbClock &lt;= not TbClock after TbPeriod/2 when TbSimEnded /= '1' else '0';

    -- EDIT: Check that clk is really your main clock signal
    clk &lt;= TbClock;

    stimuli : process
        variable num_ticks : natural;
    begin
        -- Reset generation
        reset &lt;= '1';
        wait for 20 ns;
        reset &lt;= '0';
        wait for 20 ns;
        -- Start the timer
        start &lt;= '1';
        wait for 20 ns;
        start &lt;= '0';
        stop  &lt;= '1';
        -- Adjust interval up and down
        adjust_interval_up &lt;= '1';
        wait for 10 ns;
        start              &lt;= '1';
        stop               &lt;= '0';
        adjust_interval_up &lt;= '0';
        wait for 30 ns;
        start                &lt;= '0';
        stop                 &lt;= '1';
        adjust_interval_down &lt;= '1';
        wait for 10 ns;
        start                &lt;= '1';
        stop                 &lt;= '0';
        adjust_interval_down &lt;= '0';
        wait for 20 ns;
        start              &lt;= '0';
        stop               &lt;= '1';
        adjust_interval_up &lt;= '1';
        wait for 600 ns;
        start              &lt;= '1';
        stop               &lt;= '0';
        adjust_interval_up &lt;= '0';
        -- Wait for the timer to reach the alarm interval (60 clocks)
        wait for 600 ns; -- Simulate for the required time
        -- Stop the timer
        start &lt;= '0';
        stop  &lt;= '1';
        wait for 100 ns;
        -- Stop the clock and terminate the simulation
        TbSimEnded &lt;= '1';
        wait;
    end process;
end tb;

              This should be easier to simulate, I’ve included a simulation done with Questa.

              • dejo@kbin.socialOP
                1·
                1 year ago

                @T4V0 I just now see your messages, thank you…
                In the meantime, I made something like this…
                What do you think about the specifications that the project requires, should I stick to your code or should I add something from my own code?
                Does your simulation correspond to a time of 1 hour and should there be alarming on the simulation?

                Vhdl code:

                library ieee;
                use ieee.std_logic_1164.all;
                use ieee.numeric_std.all;
                entity Kitchen_Timer is
                port (
                clk : in std_logic; – Clock input
                reset : in std_logic; – Reset input
                start : in std_logic; – Start button input
                stop : in std_logic; – Stop button input
                adjust_interval_up : in std_logic; – Button for increasing alarm interval
                adjust_interval_down : in std_logic; – Button for decreasing alarm interval
                alarm : out std_logic – Alarm output
                );
                end entity Kitchen_Timer;
                architecture Behavioral of Kitchen_Timer is
                signal count : integer range 0 to 3600000 := 0; – Adjust range for 1 hour
                signal alarming : std_logic := ‘0’;
                signal alarm_interval : integer range 600 to 3600000 := 600; – Adjust range for 1 hour
                begin
                process (clk, reset)
                begin
                if reset = ‘1’ then
                count &lt;= 0;
                alarm_interval &lt;= 600;
                elsif rising_edge(clk) then
                if start = ‘1’ then
                count &lt;= count + 1;
                end if;
                if stop = ‘1’ or count = alarm_interval then
                count &lt;= 0;
                end if;
                if adjust_interval_up = ‘1’ then
                if alarm_interval &lt; 3600000 then
                alarm_interval &lt;= alarm_interval + 600; – Adjust increment for 1 minute
                end if;
                count &lt;= 0; – Reset count when adjusting interval
                elsif adjust_interval_down = ‘1’ then
                if alarm_interval > 600 then
                alarm_interval &lt;= alarm_interval - 600; – Adjust decrement for 1 minute
                end if;
                count &lt;= 0; – Reset count when adjusting interval
                end if;
                end if;
                end process;
                alarming &lt;= ‘1’ when count >= alarm_interval else ‘0’;
                alarm &lt;= alarming;
                end architecture Behavioral;

                Testbench:

                library ieee;
                use ieee.std_logic_1164.all;
                entity tb_Kitchen_Timer is
                end tb_Kitchen_Timer;
                architecture tb of tb_Kitchen_Timer is
                component Kitchen_Timer
                port (
                clk : in std_logic;
                reset : in std_logic;
                start : in std_logic;
                stop : in std_logic;
                adjust_interval_up : in std_logic;
                adjust_interval_down : in std_logic;
                alarm : out std_logic
                );
                end component;
                signal clk : std_logic := ‘0’;
                signal reset : std_logic := ‘0’;
                signal start : std_logic := ‘0’;
                signal stop : std_logic := ‘0’;
                signal adjust_interval_up : std_logic := ‘0’;
                signal adjust_interval_down : std_logic := ‘0’;
                signal alarm : std_logic;
                constant TbPeriod : time := 20 ns;
                signal TbClock : std_logic := ‘0’;
                signal TbSimEnded : std_logic := ‘0’;
                begin
                dut : Kitchen_Timer
                port map (
                clk => clk,
                reset => reset,
                start => start,
                stop => stop,
                adjust_interval_up => adjust_interval_up,
                adjust_interval_down => adjust_interval_down,
                alarm => alarm
                );
                -- Clock generation
                TbClock &lt;= not TbClock after TbPeriod/2 when TbSimEnded /= ‘1’ else ‘0’;
                clk &lt;= TbClock;
                stimuli : process
                variable num_ticks : natural;
                begin
                -- Reset generation
                reset &lt;= ‘1’;
                wait for 200 us;
                reset &lt;= ‘0’;
                wait for 200 us;
                -- Start the timer
                start &lt;= ‘1’;
                wait for 500 us;
                -- Adjust interval up and down
                adjust_interval_up &lt;= ‘1’;
                wait for 100 us;
                adjust_interval_up &lt;= ‘0’;
                wait for 100 us;
                adjust_interval_down &lt;= ‘1’;
                wait for 100 us;
                adjust_interval_down &lt;= ‘0’;
                wait for 100 us;
                -- Wait for the timer to reach the alarm interval (3600000 clocks)
                wait for 72 ms; – Simulate for the required time
                -- Stop the timer
                start &lt;= ‘0’;
                wait for 300 us;
                -- Stop the clock and terminate the simulation
                TbSimEnded &lt;= ‘1’;
                wait;
                end process;
                end tb;

                • T4V0@kbin.social
                  1·
                  1 year ago

                  @dejo

                  What do you think about the specifications that the project requires, should I stick to your code or should I add something from my own code?

                  I would stick to my code, your alarm isn’t going to work properly due to its comparisons as I mentioned in my previous comments. But if you want to improve the code I modified, you can change the adjust_interval_up and adjust_interval_down buttons to be synchronized to their own states rather than the clock (make their own process with their signals added to the signal sensitivity list and add an extra asynchronous condition to zero the counter on the original process). If you don’t make a change like this your alarm is going to take up to an hour to adjust its timer range.

                  Does your simulation correspond to a time of 1 hour and should there be alarming on the simulation?

                  Yes, if you have a 1/60 Hertz clock signal. And you must have alarming on the simulation as it is crucial to show that it works.

                  • dejo@kbin.socialOP
                    1·
                    1 year ago

                    @T4V0
                    Is the 1/60 Hz set somewhere or is it set in the code itself?
                    When you say that I must have an “alarming” signal on the simulation, is it actually this “alarm” signal that is presented on the simulation or?
                    And, do I need to have count signal in simulation?