Hi, I’m not quite sure if this vhdl code and testbench is correct for the given task. Can you take a look?
Design a one-hour kitchen timer. The device should have buttons/switches to start and stop the timer, as well as to set the desired time interval for the alarm. Realize the task using the software package Quartus or in GHDL, confirm the correctness of the project task by simulation.
This is VHDL code:
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;
entity Kitchen_Timer is
port (
clk : in std_logic; -- Clock input
reset : in std_logic; -- Reset input
start : in std_logic; -- Start button input
stop : in std_logic; -- Stop button input
alarm : out std_logic -- Alarm output
);
end entity Kitchen_Timer;
-- Declare the architecture for the kitchen timer
architecture Behavioral of Kitchen_Timer is
signal count : integer range 0 to 3600 := 0; -- Counter for timer
signal alarming : std_logic := '0'; -- Signal to indicate alarming interval
signal alarm_en : std_logic := '0'; -- Signal to enable alarming interval
signal alarm_cnt : integer range 0 to 600 := 0; -- Counter for alarming interval
begin
-- Process to control the kitchen timer and alarming interval
process (clk, reset)
begin
if (reset = '1') then
count <= 0;
alarming <= '0';
alarm_en <= '0';
alarm_cnt <= 0;
elsif (rising_edge(clk)) then
if (stop = '1') then
count <= 0;
alarming <= '0';
alarm_en <= '0';
alarm_cnt <= 0;
elsif (start = '1' and count < 3600) then
count <= count + 1;
if (count = 3600) then
count <= 0;
alarming <= '0';
alarm_en <= '0';
alarm_cnt <= 0;
elsif (count > 0) then
alarm_en <= '1';
end if;
end if;
if (alarm_en = '1') then
if (alarm_cnt < 600) then
alarm_cnt <= alarm_cnt + 1;
else
alarm_cnt <= 0;
alarming <= '1';
end if;
end if;
end if;
end process;
-- Assign the alarm output
alarm <= alarming;
end architecture Behavioral; ```
This is Testbench:
```library ieee;
use ieee.std_logic_1164.all;
entity tb_Kitchen_Timer is
end tb_Kitchen_Timer;
architecture tb of tb_Kitchen_Timer is
component Kitchen_Timer
port (clk : in std_logic;
reset : in std_logic;
start : in std_logic;
stop : in std_logic;
alarm : out std_logic);
end component;
signal clk : std_logic;
signal reset : std_logic;
signal start : std_logic;
signal stop : std_logic;
signal alarm : std_logic;
constant TbPeriod : time := 1000 ns; -- EDIT Put right period here
signal TbClock : std_logic := '0';
signal TbSimEnded : std_logic := '0';
begin
dut : Kitchen_Timer
port map (clk => clk,
reset => reset,
start => start,
stop => stop,
alarm => alarm);
-- Clock generation
TbClock <= not TbClock after TbPeriod/2 when TbSimEnded /= '1' else '0';
-- EDIT: Check that clk is really your main clock signal
clk <= TbClock;
stimuli : process
begin
-- EDIT Adapt initialization as needed
start <= '0';
stop <= '0';
-- Reset generation
-- EDIT: Check that reset is really your reset signal
reset <= '1';
wait for 100 ns;
reset <= '0';
wait for 100 ns;
-- EDIT Add stimuli here
wait for 100 * TbPeriod;
-- Stop the clock and hence terminate the simulation
TbSimEnded <= '1';
wait;
end process;
end tb;
-- Configuration block below is required by some simulators. Usually no need to edit.
configuration cfg_tb_Kitchen_Timer of tb_Kitchen_Timer is
for tb
end for;
end cfg_tb_Kitchen_Timer;```
#science
@dejo I have made a few changes to your code:
Kitchen_Timer.vhd
library ieee; use ieee.std_logic_1164.all; use ieee.numeric_std.all; entity Kitchen_Timer is port ( clk : in std_logic; -- Clock input reset : in std_logic; -- Reset input start : in std_logic; -- Start button input stop : in std_logic; -- Stop button input adjust_interval_up : in std_logic; -- Button for increasing alarm interval adjust_interval_down : in std_logic; -- Button for decreasing alarm interval alarm : out std_logic -- Alarm output ); end entity Kitchen_Timer; architecture Behavioral of Kitchen_Timer is signal count : integer range 0 to 60 := 0; -- Adjust range for 1 hour signal alarming : std_logic := '0'; signal alarm_interval : integer range 1 to 60 := 1; -- Adjust range for 1 hour begin process (clk, reset) begin if reset = '1' then count <= 0; alarm_interval <= 1; elsif rising_edge(clk) then if start = '1' then count <= count + 1; end if; if stop = '1' then count <= 0; alarming <= '0'; end if; if count = alarm_interval then alarming <= '1'; end if; if adjust_interval_up = '1' then if alarm_interval < 60 then alarm_interval <= alarm_interval + 1; -- Adjust increment for 1 minute end if; count <= 0; -- Reset count when adjusting interval elsif adjust_interval_down = '1' then if alarm_interval > 60 then alarm_interval <= alarm_interval - 1; -- Adjust decrement for 1 minute end if; count <= 0; -- Reset count when adjusting interval end if; end if; end process; alarm <= alarming; end architecture Behavioral;tb_Kitchen_Timer.vhd
library ieee; use ieee.std_logic_1164.all; use ieee.numeric_std.all; entity tb_Kitchen_Timer is end tb_Kitchen_Timer; architecture tb of tb_Kitchen_Timer is signal clk : std_logic := '0'; signal reset : std_logic := '0'; signal start : std_logic := '0'; signal stop : std_logic := '0'; signal adjust_interval_up : std_logic := '0'; signal adjust_interval_down : std_logic := '0'; signal alarm : std_logic; constant TbPeriod : time := 10 ns; signal TbClock : std_logic := '0'; signal TbSimEnded : std_logic := '0'; begin dut : entity work.Kitchen_Timer port map ( clk => clk, reset => reset, start => start, stop => stop, adjust_interval_up => adjust_interval_up, adjust_interval_down => adjust_interval_down, alarm => alarm ); -- Clock generation TbClock <= not TbClock after TbPeriod/2 when TbSimEnded /= '1' else '0'; -- EDIT: Check that clk is really your main clock signal clk <= TbClock; stimuli : process variable num_ticks : natural; begin -- Reset generation reset <= '1'; wait for 20 ns; reset <= '0'; wait for 20 ns; -- Start the timer start <= '1'; wait for 20 ns; start <= '0'; stop <= '1'; -- Adjust interval up and down adjust_interval_up <= '1'; wait for 10 ns; start <= '1'; stop <= '0'; adjust_interval_up <= '0'; wait for 30 ns; start <= '0'; stop <= '1'; adjust_interval_down <= '1'; wait for 10 ns; start <= '1'; stop <= '0'; adjust_interval_down <= '0'; wait for 20 ns; start <= '0'; stop <= '1'; adjust_interval_up <= '1'; wait for 600 ns; start <= '1'; stop <= '0'; adjust_interval_up <= '0'; -- Wait for the timer to reach the alarm interval (60 clocks) wait for 600 ns; -- Simulate for the required time -- Stop the timer start <= '0'; stop <= '1'; wait for 100 ns; -- Stop the clock and terminate the simulation TbSimEnded <= '1'; wait; end process; end tb;This should be easier to simulate, I’ve included a simulation done with Questa.
@T4V0 I just now see your messages, thank you…
In the meantime, I made something like this…
What do you think about the specifications that the project requires, should I stick to your code or should I add something from my own code?
Does your simulation correspond to a time of 1 hour and should there be alarming on the simulation?
Vhdl code:
library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;
entity Kitchen_Timer is
port (
clk : in std_logic; – Clock input
reset : in std_logic; – Reset input
start : in std_logic; – Start button input
stop : in std_logic; – Stop button input
adjust_interval_up : in std_logic; – Button for increasing alarm interval
adjust_interval_down : in std_logic; – Button for decreasing alarm interval
alarm : out std_logic – Alarm output
);
end entity Kitchen_Timer;
architecture Behavioral of Kitchen_Timer is
signal count : integer range 0 to 3600000 := 0; – Adjust range for 1 hour
signal alarming : std_logic := ‘0’;
signal alarm_interval : integer range 600 to 3600000 := 600; – Adjust range for 1 hour
begin
process (clk, reset)
begin
if reset = ‘1’ then
count <= 0;
alarm_interval <= 600;
elsif rising_edge(clk) then
if start = ‘1’ then
count <= count + 1;
end if;
if stop = ‘1’ or count = alarm_interval then
count <= 0;
end if;
if adjust_interval_up = ‘1’ then
if alarm_interval < 3600000 then
alarm_interval <= alarm_interval + 600; – Adjust increment for 1 minute
end if;
count <= 0; – Reset count when adjusting interval
elsif adjust_interval_down = ‘1’ then
if alarm_interval > 600 then
alarm_interval <= alarm_interval - 600; – Adjust decrement for 1 minute
end if;
count <= 0; – Reset count when adjusting interval
end if;
end if;
end process;
alarming <= ‘1’ when count >= alarm_interval else ‘0’;
alarm <= alarming;
end architecture Behavioral;
Testbench:
library ieee;
use ieee.std_logic_1164.all;
entity tb_Kitchen_Timer is
end tb_Kitchen_Timer;
architecture tb of tb_Kitchen_Timer is
component Kitchen_Timer
port (
clk : in std_logic;
reset : in std_logic;
start : in std_logic;
stop : in std_logic;
adjust_interval_up : in std_logic;
adjust_interval_down : in std_logic;
alarm : out std_logic
);
end component;
signal clk : std_logic := ‘0’;
signal reset : std_logic := ‘0’;
signal start : std_logic := ‘0’;
signal stop : std_logic := ‘0’;
signal adjust_interval_up : std_logic := ‘0’;
signal adjust_interval_down : std_logic := ‘0’;
signal alarm : std_logic;
constant TbPeriod : time := 20 ns;
signal TbClock : std_logic := ‘0’;
signal TbSimEnded : std_logic := ‘0’;
begin
dut : Kitchen_Timer
port map (
clk => clk,
reset => reset,
start => start,
stop => stop,
adjust_interval_up => adjust_interval_up,
adjust_interval_down => adjust_interval_down,
alarm => alarm
);
-- Clock generation
TbClock <= not TbClock after TbPeriod/2 when TbSimEnded /= ‘1’ else ‘0’;
clk <= TbClock;
stimuli : process
variable num_ticks : natural;
begin
-- Reset generation
reset <= ‘1’;
wait for 200 us;
reset <= ‘0’;
wait for 200 us;
-- Start the timer
start <= ‘1’;
wait for 500 us;
-- Adjust interval up and down
adjust_interval_up <= ‘1’;
wait for 100 us;
adjust_interval_up <= ‘0’;
wait for 100 us;
adjust_interval_down <= ‘1’;
wait for 100 us;
adjust_interval_down <= ‘0’;
wait for 100 us;
-- Wait for the timer to reach the alarm interval (3600000 clocks)
wait for 72 ms; – Simulate for the required time
-- Stop the timer
start <= ‘0’;
wait for 300 us;
-- Stop the clock and terminate the simulation
TbSimEnded <= ‘1’;
wait;
end process;
end tb;
@dejo
I would stick to my code, your alarm isn’t going to work properly due to its comparisons as I mentioned in my previous comments. But if you want to improve the code I modified, you can change the
adjust_interval_upandadjust_interval_downbuttons to be synchronized to their own states rather than the clock (make their own process with their signals added to the signal sensitivity list and add an extra asynchronous condition to zero the counter on the original process). If you don’t make a change like this your alarm is going to take up to an hour to adjust its timer range.Yes, if you have a 1/60 Hertz clock signal. And you must have alarming on the simulation as it is crucial to show that it works.
@T4V0
Is the 1/60 Hz set somewhere or is it set in the code itself?
When you say that I must have an “alarming” signal on the simulation, is it actually this “alarm” signal that is presented on the simulation or?
And, do I need to have count signal in simulation?
@dejo
You would set that on the testbench or on your synthesis code, but that is unnecessary, I only said that in case if you tested it on a actual FPGA. If you do that on your testbench, it would take a very long time to simulate.
The
alarmsignal. The “alarming” is when thealarmsignal is in a high logic state.I wouldn’t say it’s mandatory, but it is a good addition to the simulation, keep it.
@T4V0 Thanks a lot for your help, I appreciate it.
@T4V0 How to How can I include the count signal in the simulation so that it is displayed to me
Shouldn’t the alarm signal last longer when the alarm interval is increased?
@T4V0
@dejo No, the alarm signal takes a longer time to start rather than the interval when it’s set.
You seem to have some trouble picturing the Kitchen Timer itself.
Kitchen timer
Here, when you change the time interval it’s the same as when you turn the knob. So it doesn’t last longer when you increase the timer, it just takes longer for it to activate.
@T4V0 Thank you so much.
@dejo In your .do script file add this line:
add wave -label "count" -radix unsigned /dut/Kitchen_Timer/count@T4V0 I use Notepad to write scripts.I don’t think it works that way with the code written like this
**library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;
entity tb_Kitchen_Timer is
end tb_Kitchen_Timer;
architecture tb of tb_Kitchen_Timer is
signal clk : std_logic := ‘0’;
signal reset : std_logic := ‘0’;
signal start : std_logic := ‘0’;
signal stop : std_logic := ‘0’;
signal adjust_interval_up : std_logic := ‘0’;
signal adjust_interval_down : std_logic := ‘0’;
signal alarm : std_logic;
constant TbPeriod : time := 10 ns;
signal TbClock : std_logic := ‘0’;
signal TbSimEnded : std_logic := ‘0’;
begin
dut : entity work.Kitchen_Timer
port map
(
clk => clk,
reset => reset,
start => start,
stop => stop,
adjust_interval_up => adjust_interval_up,
adjust_interval_down => adjust_interval_down,
alarm => alarm
)
TbClock <= not TbClock after TbPeriod/2 when TbSimEnded /= ‘1’ else ‘0’; – Clock generation
clk <= TbClock;
stimuli : process
variable num_ticks : natural;
begin
-- Reset generation
reset <= ‘1’;
wait for 20 ns;
reset <= ‘0’;
wait for 20 ns;
-- Start the timer
start <= ‘1’;
wait for 20 ns;
start <= ‘0’;
stop <= ‘1’;
-- Adjust interval up and down
adjust_interval_up <= ‘1’;
wait for 10 ns;
start <= ‘1’;
stop <= ‘0’;
adjust_interval_up <= ‘0’;
wait for 30 ns;
start <= ‘0’;
stop <= ‘1’;
adjust_interval_down <= ‘1’;
wait for 10 ns;
start <= ‘1’;
stop <= ‘0’;
adjust_interval_down <= ‘0’;
wait for 20 ns;
start <= ‘0’;
stop <= ‘1’;
adjust_interval_up <= ‘1’;
wait for 600 ns;
start <= ‘1’;
stop <= ‘0’;
adjust_interval_up <= ‘0’;
-- Wait for the timer to reach the alarm interval (60 clocks)
wait for 600 ns; – Simulate for the required time
-- Stop the timer
start <= ‘0’;
stop <= ‘1’;
wait for 100 ns;
-- Stop the clock and terminate the simulation
TbSimEnded <= ‘1’;
wait;
end process;
end tb;
**
@dejo Whoops, I made a mistake, you don’t need to include the entity when simulating. This line bellow should be the correct one:
add wave -label "count" -radix unsigned /dut/countThis is my .do file (when using Modelsim or Questa, change to the directory with all the .vhd files and the .do file and execute the command
do tb.do):tb.do#Creates project's library vlib work #Compiles project with VHDL93 standard: all files used in the testbench. They should be compiled in order of dependency. vcom -93 Kitchen_Timer.vhd testbench.vhd #Simulates (work is the directory, tb_Kitchen_Timer is the entity's name). #The argument -voptargs="+acc" is necessary to disable signal optimization in Questa. vsim -voptargs="+acc" -t ns work.tb_Kitchen_Timer #Show waveforms. view wave #Add specific signals. # -radix: binary, hex, dec, unsigned. # -label: wave's name. add wave -label "clk" -radix binary /clk add wave -label "reset" -radix binary /reset add wave -label "start" -radix binary /start add wave -label "stop" -radix binary /stop add wave -label "adjust_interval_up" -radix binary /adjust_interval_up add wave -label "adjust_interval_down" -radix binary /adjust_interval_down add wave -label "alarm" -radix binary /alarm add wave -label "count" -radix unsigned /dut/count add wave -label "TbClock" -radix binary /TbClock add wave -label "TbSimEnded" -radix binary /TbSimEnded #Simulate for 1500 ns. run 1500ns # Zoom to fit entire window. wave zoomfull write wave wave.psI’ve also included the simulation result.