Fully Charged in Just 6 Minutes – Groundbreaking Technique Could Revolutionize EV Charging::Typically, it takes around 10 hours to charge an electric vehicle. Even with fast-charging techniques, you’re still looking at a minimum of 30 minutes – and that’s if there’s an open spot at a charging station. If electric vehicles could charge as swiftly as we refill traditional gas vehicles, it wo

  • evranch@lemmy.ca
    link
    fedilink
    English
    arrow-up
    26
    ·
    10 months ago

    Possibly even more significant, those are some large cables and even larger contacts required. There’s no way a 1MW disconnect is just a little plug you stick into your car.

    In fact as an electrician I can’t think of anything even near megawatt class that would be connected with a portable cord, or at a voltage that would be safe for consumers to handle.

    Maybe someone in the mining industry or similar can chime in, but I currently run a pumping station that includes 3000HP motors (2.2MW). These are 4kV 3 phase units where each phase cable is as thick as your arm. All connections are bolted and taped to avoid corona discharge. Just dragging the cable to the car would be more than the average driver could handle.

    I don’t see a way to get these power levels into a car short of a standardized and semi-automated docking system. Or maybe go back to the idea of standard swappable batteries where the battery then is charged rapidly for the next customer.

    • DreadPotato@sopuli.xyz
      link
      fedilink
      English
      arrow-up
      16
      ·
      edit-2
      10 months ago

      The power lines in the cable are disconnected inside the charger by a contactor until communication with the car is confirmed established with a handshake, and then it connects power to the cable. If the communication with the car drops at any point, the contactor disconnects the power to the cable. It requires both effort and knowledge to bypass this design, it basically can’t happen accidentally.

      Also, the cables you mention are that large, because they’re passively cooled, DC car chargers have watercooled cables so they can be much thinner without overheating. And at 4kV you’re looking at significantly different insulation thickness as well, compared to the 400-800V that electric cars use.

    • zoe @infosec.pub
      link
      fedilink
      English
      arrow-up
      2
      ·
      edit-2
      10 months ago

      u wouldnt plug in and plug out the thing live in a charger, no ? the charging station should detect when the car is plugged then activates some form of disconnect or something, to allow a 1Mw power to flow lol ? also 1Mw is far fetched, and the 6 min charging time is absurd. 12 min at 500 Kw speed would be more plausible

    • Virtual Insanity @lemmy.world
      link
      fedilink
      English
      arrow-up
      2
      ·
      10 months ago

      That’s 4,350 amps @230vac. The service fuse for my entire home is 80 or 100amp (single phase domestic dwelling Australia). The main breaker is 63amp.

      • spongebue@lemmy.world
        link
        fedilink
        English
        arrow-up
        3
        ·
        10 months ago

        DC fast charging typically runs at 400 volts, with some cars doing 800. They also do it with highly specialized equipment and service lines you’d never see in a residential setting.

        When charging at home, you have all night. A 50A circuit will go 0-100 on most cars in that time, and if you look at what most people actually drive you can generally get by on much less.

        • zoe @infosec.pub
          link
          fedilink
          English
          arrow-up
          1
          arrow-down
          1
          ·
          edit-2
          10 months ago

          how much amperage does utilities allow for residential use ? imagine charging ur car at 50 amp and decide to turn the heater on, only to trigger the breaker and cause the house to go dark lol. also home charging is costly as heck. 80kwh each night, wth ? u probably need 75m² of solar to generate electricity for 5 hours, generating 75kwh, enough to fully charge ur car for free, but also u need 7*11kwh powerpacks to accomodate all this energy. seems costly as hell. unless also ur job offers supercharger parking, which would be more suitable

          • spongebue@lemmy.world
            link
            fedilink
            English
            arrow-up
            1
            ·
            10 months ago

            how much amperage does utilities allow for residential use ? imagine charging ur car at 50 amp and decide to turn the heater on, only to trigger the breaker and cause the house to go dark lol

            A fair question. Depends on the house. 100-200 is common, depending on the age of the house. 100 or less if your house predates central air conditioning, and 150-200 is far more common in the last few decades. Most people charge overnight, and they’re not using much else. If you truly have a smaller connection, even 20A @240V is surprisingly useful. Or hell, a normal outlet.

            80kwh each night, wth ?

            That may be your battery’s capacity, but that’s not necessarily your draw. How big is your gas tank? Do you give it ~15 gallons each day? My car gets about 3.5 miles per kWh. If I drive it 70 miles, that’s 20 kWH and then the car stops charging. And I pay about $2.50 for it. What would gas cost?

            u probably need 75m² of solar to generate electricity for 5 hours, generating 75kwh, enough to fully charge ur car for free, but also u need 7*11kwh powerpacks to accomodate all this energy. seems costly as hell.

            Solar direct to car is actually a terrible idea. Just hook something up to the grid if you want solar, but it’s pretty cheap without. You’re overthinking it, probably because your 80 kWH per day number is so out of whack.

            unless also ur job offers supercharger parking, which would be more suitable

            Again, no. Well, it’s cool if you can get it but it’s really not needed because home electricity is generally way cheaper than gasoline.

      • Chreutz@lemmy.world
        link
        fedilink
        English
        arrow-up
        3
        ·
        10 months ago

        Fast charging uses up to 1000 V DC, and the current limits of conductors are typically set by the temperature it reaches when conduction losses heat them up. This can be (and is) offset by liquid cooling, allowing current installations to deliver up to 650 A (Tesla supercharger v3).

        With improvements, it’s not far off 1 MW.